CASE STUDY OF A DISTAL FEMUR TI6Al4V LOCKED COMPRESSION PLATE FAILURE SURFACE INVESTIGATION AND FINITE ELEMENT ANALYSIS

Basit Öğe Kaydı
dc.authoridBahce, Erkan/0000-0001-5389-5571
dc.contributor.authorCan, Murat
dc.contributor.authorOymak, Mehmet Akif
dc.contributor.authorKoluacik, Serdar
dc.contributor.authorBahce, Erkan
dc.contributor.authorUzunyol, Omer Faruk
dc.date.accessioned2024-08-04T20:54:46Z
dc.date.available2024-08-04T20:54:46Z
dc.date.issued2024
dc.departmentİnönü Üniversitesien_US
dc.description.abstractIn this study, the failure of locking compression plates (LCP) used in the treatment of bone fractures resulting from falls in orthopedic patients at Malatya Training and Research Hospital was investigated. The researchers examined the fracture surface of the failed Ti6Al4V LCP using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) images. The fracture pattern of the plate caused by the fall was replicated in a computer-aided design (CAD) model, obtained through three-dimensional (3D) scanning. Additionally, a CAD model of the femur bone was created using magnetic resonance (MR) images. The assembled images of the replicated fracture and the femur bone were used to simulate the application of locked and unlocked compression screws. Considering the weight-bearing load on a human femur, a linear load of 1200 N and 300 N iliopsoas 300 N abductor 600 N hip contact and 70 N tensor fascia latea walking loads had been applied using finite element analysis (FEA). The researchers analyzed the total deformations, von Mises stress, and principal stresses of the plate. When FEA was conducted with walking and body forces applied, it was observed that the walking forces resulted in a 20% higher von Mises stress and a 22.5% greater total deformation 15% low cycle fatigue compared to the body force. During the analysis with walking forces applied, it was noticed that the maximum von Mises stresses on the LCP and the point where fatigue initiation began coincided with the fracture site of the LCP in the patient's body. However, this observation was in contrast to the analysis with body loads applied.en_US
dc.identifier.doi10.1142/S0219519423500951
dc.identifier.issn0219-5194
dc.identifier.issn1793-6810
dc.identifier.issue4en_US
dc.identifier.scopus2-s2.0-85174202766en_US
dc.identifier.scopusqualityQ4en_US
dc.identifier.urihttps://doi.org/10.1142/S0219519423500951
dc.identifier.urihttps://hdl.handle.net/11616/101626
dc.identifier.volume24en_US
dc.identifier.wosWOS:001083087300003en_US
dc.identifier.wosqualityQ4en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherWorld Scientific Publ Co Pte Ltden_US
dc.relation.ispartofJournal of Mechanics in Medicine and Biologyen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectFemuren_US
dc.subjectLCP failureen_US
dc.subjectTi6Al4Ven_US
dc.subjectbreakage surfaceen_US
dc.subjectfinite element analysisen_US
dc.titleCASE STUDY OF A DISTAL FEMUR TI6Al4V LOCKED COMPRESSION PLATE FAILURE SURFACE INVESTIGATION AND FINITE ELEMENT ANALYSISen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu