Comparison of Time-dependent Two-dimensional and Three-dimensional Stability with Micro-computerized Tomography and Wettability of Three Impression Materials

Basit Öğe Kaydı
dc.authoridAvcu, Guler Yildirim/0000-0002-8461-7774
dc.authorwosidMalkoc, Meral Arslan/AAC-5742-2021
dc.authorwosidyildirim avcu, guler/K-2278-2017
dc.authorwosidAvcu, Guler Yildirim/ABG-9821-2020
dc.contributor.authorKaraaslan, G.
dc.contributor.authorMalkoc, M. A.
dc.contributor.authorYildirim, G.
dc.contributor.authorMalkoc, S.
dc.date.accessioned2024-08-04T20:44:39Z
dc.date.available2024-08-04T20:44:39Z
dc.date.issued2018
dc.departmentİnönü Üniversitesien_US
dc.description.abstractObjectives: The objective of this study is to explore time-dependent dimensional stability of three different elastomeric impression materials -vinyl polyether silicone (VPES), vinyl polysiloxane (VPS), and polyether (PE) -through micro-computerized tomography (mu -CT) imaging, allows three-dimensional (3D) imaging and measurement without sample preparation or chemical fixation. Materials and Methods: Thirty specimens were created using 3 mm high, 30 mm wide Teflon molds (n = 10). Specimens were scanned with mu -CT on the 1st (T1) h and 1st (T2), 7th (T3), and 14th (T4) days. 3D models were created at the above-mentioned times, volumetric measurements were conducted and dimensional changes were calculated. Diameters and heights of each impression material were measured with 2D analyses. Furthermore, contact angle measurements of these elastomeric impression materials were collected using the sessile drop method during and after polymerization at 0, 2, 5, 20, 60, 120, and 240 s These measurements were made on specimens (n = 10) prepared in standard sizes using a 50 mu m deep stainless steel die with dimensions of 62 mm x 20 mm x 3 mm. Results: Evaluation of the dimensional volume changes of the VPES, VPS, and PE measurements showed there to be no statistically significant differences between the T1, T2, T3, and T4 (P > 0.05). Only the decreases in the volume averages of T3 and T4 in the VPES were statistically significant (P < 0.05). As a result of binary comparisons, the evaluation of contact angle measurements of VPES, VPS, and PE materials during and after polymerization were compared. The average contact angle measurements of the VPS group were statistically significantly lower than the averages of the VPES and PE groups (P < 0.01). Conclusions: VPS was found to be the most stable impression material concerning dimensional change and wettability.en_US
dc.identifier.doi10.4103/njcp.njcp_314_17
dc.identifier.endpage920en_US
dc.identifier.issn1119-3077
dc.identifier.issue7en_US
dc.identifier.pmid29984725en_US
dc.identifier.scopus2-s2.0-85050103774en_US
dc.identifier.scopusqualityQ3en_US
dc.identifier.startpage912en_US
dc.identifier.urihttps://doi.org/10.4103/njcp.njcp_314_17
dc.identifier.urihttps://hdl.handle.net/11616/98386
dc.identifier.volume21en_US
dc.identifier.wosWOS:000439047000016en_US
dc.identifier.wosqualityQ4en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.indekslendigikaynakPubMeden_US
dc.language.isoenen_US
dc.publisherWolters Kluwer Medknow Publicationsen_US
dc.relation.ispartofNigerian Journal of Clinical Practiceen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectContact angleen_US
dc.subjectdimensional stabilityen_US
dc.subjectelastomeric impression materialsen_US
dc.subjectmicro-computerized tomographyen_US
dc.titleComparison of Time-dependent Two-dimensional and Three-dimensional Stability with Micro-computerized Tomography and Wettability of Three Impression Materialsen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
PubMed İndeksli Yayın Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu