Investigation of material removal rate (MRR) and wire wear ratio (WWR) for alloy Ti6Al4 V exposed to heat treatment processing in WEDM and optimization of parameters using Grey relational analysis

Basit Öğe Kaydı
dc.authoridAltuğ, Mehmet/0000-0002-4745-9164
dc.authorwosidAltuğ, Mehmet/ABF-5670-2020
dc.contributor.authorAltug, Mehmet
dc.date.accessioned2024-08-04T20:44:34Z
dc.date.available2024-08-04T20:44:34Z
dc.date.issued2016
dc.departmentİnönü Üniversitesien_US
dc.description.abstractThe study examines the changes of the microstructural, mechanical and conductivity characteristics of the titanium alloy Ti6Al4 V as a result of heat treatment using wire electrical discharge machining, and their effect on machinability. By means of optical microscopy and scanning electron microscopy (SEM), analyses have been performed to determine various characteristics and additionally, microhardness and conductivity measurements have been conducted. Material removal rate (MRR) and wire wear ratio (WWR) values have been determined by using L-18 Taguchi test design. The microstructures of the samples have been changed by thermal procedures. Results have been obtained by using the Grey relational analysis (GRA) optimization technique to solve the maximum MRR and minimum WWR values. The best (highest) MRR value is obtained from sample E which was water quenched in dual phase processing. The microstructure of this sample is composed of primary a and alpha' phases. The best (lowest) WWR value is obtained from sample A.en_US
dc.description.sponsorshipInonu University Scientific Researches Projects [2012/165]; Inonu University, Malatya, Turkeyen_US
dc.description.sponsorshipThis study is supported by Inonu University Scientific Researches Projects with number 2012/165. The authors thank Inonu University, Malatya, Turkey for providing financial support for the project.en_US
dc.identifier.doi10.3139/120.110916
dc.identifier.endpage805en_US
dc.identifier.issn0025-5300
dc.identifier.issue9en_US
dc.identifier.scopus2-s2.0-85048272569en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.startpage794en_US
dc.identifier.urihttps://doi.org/10.3139/120.110916
dc.identifier.urihttps://hdl.handle.net/11616/98330
dc.identifier.volume58en_US
dc.identifier.wosWOS:000387243800015en_US
dc.identifier.wosqualityQ4en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherCarl Hanser Verlagen_US
dc.relation.ispartofMaterials Testingen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectTi6Al4Ven_US
dc.subjectheat treatmenten_US
dc.subjectmaterial removal rate (MRR)en_US
dc.subjectwire wear ratio (WWR)en_US
dc.subjectGrey relational analysis (GRA)en_US
dc.titleInvestigation of material removal rate (MRR) and wire wear ratio (WWR) for alloy Ti6Al4 V exposed to heat treatment processing in WEDM and optimization of parameters using Grey relational analysisen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu